Color-user-defined 120μm film thickness asphalt batching plant with
37KW windlass winch system
Finished product hoppers/ready product bin introduction
A. Operation methods
The asphalt mixture is discharged from mixer to trolley, which has
4 wheels and supported by rail. The trolley empties mixture to
finished product hoppers when it reaches a presetted position along
B. Finished product hopper
The trolley empties mixture to several hoppers with different
capacity. On the underside cone of finished product hopper, there
is hot oil pipeline for purpose of heat-preservation. Every hopper
has heat insulation, electrothermal component installed on
Commonly, it is suggested to discharge 500 kg material every 2
hours to avoid difficulty in dealing with it.
C. Waste hopper
Waste hopper is located before main hoppers. Its capacity is about
2 times the one of mixer.
Electric gliding coping can preserve heat. Once operator choose one
hopper to discharge material, its coping will open before trolley
moving from under mixer.
E. Protector (limit switch)
Mechatronics lever mode limit switch, which can avoid offside due
to wrong operating, is upon rail.
When trolley contacts limit switch, its control circuit breaks off
and trolley stops.
F. Windlass buildup
Windlass is constituted of electromotor, reducer, brake, and
roller. This set is installed on the base of finished product
hopper. Roller is installed on supporting frame. Refer to
manufacturer specification for details about reducer lubrication.
G. Delivery trolley
⑴. Frequency conversion controller on console controls the trolley
position. Approaching sensor controls the discharging position for
each hopper, namely, through measuring the position change of
trolley relativing to presetted point on rail.
Before trolley reaching presetted-discharging point, operator has
presetted the discharging position. Along with trolley tracking
forward and contacting bumping-block, air cylinder turns over the
bumping-block. The trolley door is pushed backward. Whit trolley
moving on, its emptying door opens and mixture discharges. After
emptying, the tensioning spring will pull back the door.
⑶. Spring tension
After trolley installed, tensioning springs, which used for
promoting discharging door must be adjusted correctly. When empty
trolley stops tipsily on rail, adjust tensioning springs to enable
them to shut off the door.
Tensioning bolts may need to be readjusted in use.
H. Braking system
⑴. Running security for the trolley depends on brake. During
running, hydraulic handspike prop up lever and two tiles hugged on
brake wheel; when trolley stops, the handspike falls back, and
tiles hug brake wheel tightly under spring pressure.
⑵. During adjusting braker, ensure the handspike back-journey
having 10mm space and check it often, or, the braker will not act
well. Tightening the spring can increase braking force; adjust this
force to keep loaded-trolley ceasing.
If spring is over tensioned, the agile operation of hydraulic
handspike will be influenced.
|Finished product bin Maintenance|
|1||Keep trolley clean, especially for space around emptying door. Use
thinner to rinse trolley after every day using, and rinse
discharging doors of finished product hoppers periodically to
enable them to run smoothly.|
|2||Keep sufficient tension for trolley steel wires, not allow them to
bump with rail or be felted with asphalt.|
|3||Maintain proper braking moment according to specification of
hydraulic braker provided by manufacturer.|
|4||Check all mechanical limit switches for security and level
position. Wipe exposed parts with grease. Check mechatronics levers
and accessory of limit switch for security every week.|
|5||Lubricate roller bearings, trolley wheel bearings, hydraulic
braking joints and discharging door bearings every week.|
|6||Check bearings and wheels of trolley gliding door for moving.
Lubricate them if necessary.|
|7||Check oil level of windlass gearbox every week, and add to highest
level if necessary. Exchange new oil every 6 months, refer to
manual for operation detail.|
|8||Check all steel wires with eyes every week. Replace those abraded
and damaged wires immediately, and check wire binder for tension.|
|9||Check trolley for running freedom with eyes.|
|10||Keep rail clean.|
|11||Keep gliding door of finished product hoppers agile.|